-
For use with RowErg, Model C, D, E and Dynamic Indoor Rowers. This is one of the small bottom seat rollers (two per machine; sold individually) that runs under the top edge of the monorail. Includes mounting hardware (nut, bolt and spacers) that hold the roller on the seat frame. -
For use with RowERG, Model D and E Indoor Rowers. This is the housing into which a sensor coil sits. *** SENSOR COIL NOT INCLUDED *** Replacement Instructions (also available at concept2.co.uk/service): -
One full rake of sweep bushings for 13mm pins. Bushings are sold in units called rakes. Each rake of pitch bushings is enough for two oarlocks. Bushings allow for pitch adjustment anywhere from one to seven degrees. -
This is a replacement LCD for PM3 and PM4 monitors. If your LCD is cracked or damaged, you can replace it with this part. Compatible with PM3 and PM4 monitors only. (Also available at concept2.co.uk/support): -
Chain Idler Pulley
-
For use on all BikeErgs. -
FREE SHIPPINGBikeERG fit guide/sizing chart LOW seat retrofit assembly – PN 2855. This will change the seat height range to 28.75 in–38 in (73 cm–97 cm). Suitable for inside leg measurements between 26 in–35 in (66 cm–89 cm).u.Warranty
Concept2 BikeErgs are backed by a limited 2-year and 5-year warranty. Complete warranty information can be found here: BikeErg Warranty(PDF) -
- Adjustable replacement handle (5cm) made from contoured orange rubber. Finger-sized radial contours and brushed texture. Solid, durable material. Available in two diameters: 32mm (thin) or 33.5mm (medium). Available separately.
-
Nut #10 SS (Flywheel cover nut) [for PN1276] -
Sale!
It's hard. It's black. It's not plastic. That's good. And contains 500,000,000 micro-mililitres of powered up H2O. In other words - it's a 500ml steel bottle for your water. Get one. Forget it somewhere - Buy another. -
FREE SHIPPINGGarmin chest belt for displaying heart rate data on the Performance Monitor. -
The elastic replacement shock cord (or bungee cord) for Slides - two required per slide. -
ROWfit offer the full range of Concept2 Sweep & Sculling Oars along with Swift Racing Sculling oars. We also service and repair all brands of oars to keep you on the water. Contact us at 087 338 3267 or 087 768 0636 to discuss the options available and get blades to match your needs. Here's a handy link to whet your appetite: https://www.concept2.co.uk/oars -
For use with model C, D and E RowErgs. -
For use with RowErgs, Model D Indoor Rowers manufactured from November 2006–present and Model E Indoor Rowers. -
For use on SkiErgs manufactured from August 2014–present. Used at the top bracket and frame cap. There are 4 of part PN2834 in the SkiErg. SkiErg Schematics -
For use on all BikeErgs crank arms. Two per crank arm -
For use on all BikeErgs. -
This special nut tool is required to replace the flywheel axle sprockets on Model C, D or E Indoor Rowers. Model D and E Axle and Sprocket Replacement -
For use on all Model C, D and E Indoor Rowers. This is the rubber bearing cup that holds the 17mm bearing (part number 1300, sold separately) -
For use on all Model C, D and E Indoor Rowers. This is the 17mm bearing located outside of the flywheel. The corresponding bearing cup (part number 1012) is sold separately. -
For use on all Model B, C, D, E and Dynamic Indoor Rowers. This is the R8 bearing located outside of the flywheel. The corresponding bearing cup (part number 1013 or 258 depending on which model you have) is sold separately. -
For use on all Model C, D, E and Dynamic Indoor Rowers as well as all SkiErgs. This is the rubber bearing cup that holds the R8 bearing on indoor rowers (part number 232, sold separately) and the 12mm bearing on SkiErgs. -
6mm L-Key (or Allen Key) for use in assembling and maintaining the Concept 2 BikeERG -
T27 6-Lobe driver required to assemble & tighten most screws and fasteners on Concept 2 machines since 2015. Use only with 6-lobe Torx screws & fasteners. -
For use on all BikeErgs. This is the internal cable and sensor on the BikeErg, that goes from the flywheel to the generator. -
For use on Compression Members with Model D Indoor Rowers manufactured from November 2006–present and Model E Indoor Rowers. -
For use with Model D Indoor Rowers manufactured from November 2006–present and Model E Indoor Rowers. -
This is the flywheel cover bolt for the Model D and E Indoor Rower and all SkiErgs. Four per machine. -
Out of stock
For use with the black SkiErg2 -
For use on all PM4 and PM5 monitors. This thumbscrew enables you to remove the battery door without tools. -
This is a replacement battery door for the PM5.
