- Adjustable replacement handle (5cm) made from contoured orange rubber. Finger-sized radial contours and brushed texture. Solid, durable material. Available in two diameters: 32mm (thin) or 33.5mm (medium). Available separately.
-
-
ROWfit offer the full range of Concept2 Sweep & Sculling Oars along with Swift Racing Sculling oars. We also service and repair all brands of oars to keep you on the water. Contact us at 087 338 3267 or 087 768 0636 to discuss the options available and get blades to match your needs. Here's a handy link to whet your appetite: https://www.concept2.co.uk/oars -
- Adjustable replacement handle (5cm) made from contoured orange rubber. Finger-sized radial contours and brushed texture. Solid, durable material. Available in two diameters: 32mm (thin) or 33.5mm (medium). Available separately.
-
Used in various places with Model D and Model E Indoor Rowers manufactured from August 2006–present. -
1238 Screw, 6-lobe, 1/4-20 x 3/8; This is the handle hook screw on the Model C, D and E Indoor Rower.
1253 Screw, 6-lobe, 1/4-20 x 5/8, epoxy; Used in various places on the Model C, D and E Indoor Rower and the gray SkiErg manfactured between July 2009–July 2014.1201 6-LOBE T-27 1/4-20 X 3/4 SS PATCHED; Used on the guide bracket of Model D Indoor Rowers, and on the rear leg of Model C and D Indoor Rowers.
1231 Screw, 6-lobe, 1/4-20 x 1/2, epoxy; Used in various places on the Model C, D and E Indoor Rower.
2233 Screw 6 Lobe 1/4 – 20 x 3/4 SS Epoxy Patch; Used to attach front legs to the main body of the RowERG 1299 6 Lobe Screw 1/4 - 20 x 1/2 SS; Used in various places on the Model C, D and E Indoor Rower and BikeERG 1275 Nut, No. 6—D, E, Dynamic and SkiErg. This nut is used with the perf outlet connector. -
For use with Model D and Model E Indoor Rowers manufactured from August 2006–present. This screw is used on the foot stretcher bellies and two required for P/N 1101 Hanger Shaft, threaded. For master schematics of all model indoor rowers, visit Manuals and Schematics. -
This is the flywheel cover bolt for the Model D and E Indoor Rower and all SkiErgs. Four per machine. -
For use on Compression Members with Model D Indoor Rowers manufactured from November 2006–present and Model E Indoor Rowers. -
Nut #10 SS (Flywheel cover nut) [for PN1276] -
For use on all PM4 and PM5 monitors. This thumbscrew enables you to remove the battery door without tools. -
For use on all Model C, D, E and Dynamic Indoor Rowers as well as all SkiErgs. This is the rubber bearing cup that holds the R8 bearing on indoor rowers (part number 232, sold separately) and the 12mm bearing on SkiErgs. -
For use on all Model C, D and E Indoor Rowers. This is the rubber bearing cup that holds the 17mm bearing (part number 1300, sold separately) -
SWEEP Oarlock Universal Bushing, 13mm, Blue (Two required per oarlock)
-
SCULL Oarlock Universal Bushing, 13mm, Blue (Two required per oarlock)
-
For use on all BikeErgs crank arms. Two per crank arm -
The elastic replacement shock cord (or bungee cord) for Slides - two required per slide. -
For use on all Model C, D and E Indoor Rowers. This swivel bushing is installed at the swivel/handle end of the chain to prolong chain life and provide smoother rowing. See more info. -
Out of stock
This is the nut that keeps the gate closed on a Concept2 oarlock. Fits scull and sweep oarlocks. -
This is a replacement battery door for the PM5. -
For use with Model D Indoor Rowers manufactured from November 2006–present and Model E Indoor Rowers. -
For use with a PM5, PM4 or PM3, the smartphone holder slides onto the top of the PM to provide a place for your mobile device while using the RowErg, SkiErg or BikeErg. -
For use with green or black sleeves, our CLAM (short for "Clip-on Load Adjusting Mechanism") is a 1 cm thick shim that clips onto your oar sleeve next to the collar, allowing you to quickly and easily adjust load without any tools. -
For use with green or black sleeves, our CLAM (short for "Clip-on Load Adjusting Mechanism") is a 1 cm thick shim that clips onto your oar sleeve next to the collar, allowing you to quickly and easily adjust load without any tools. -
For use on all Model B, C, D, E and Dynamic Indoor Rowers. This is the R8 bearing located outside of the flywheel. The corresponding bearing cup (part number 1013 or 258 depending on which model you have) is sold separately. -
For use with RowErgs, Model D Indoor Rowers manufactured from November 2006–present and Model E Indoor Rowers. -
For use with all Model D and Model E Indoor Rowers manufactured from August 2006–present. Two P/N 1243 Hex Cap Screw (For hanger shafts) may be required. For master schematics of all model indoor rowers, visit Manuals and Schematics. -
For use on all Model C, D and E Indoor Rowers. This is the 17mm bearing located outside of the flywheel. The corresponding bearing cup (part number 1012) is sold separately. -
For use on SkiErgs manufactured from August 2014–present. Used at the top bracket and frame cap. There are 4 of part PN2834 in the SkiErg. SkiErg Schematics -
Chain Idler Pulley
-
6mm L-Key (or Allen Key) for use in assembling and maintaining the Concept 2 BikeERG -
This footstrap will only work for indoor rowers made after July 21, 2006. If your indoor rower was made before July 21, 2006, order P/N 1501 Footstrap (Single) Model A, B, C & Early D - 60cm/24"
instead. Replacement nylon footstrap with buckle, approximately 75cm long by 2.5cm wide, with a screw hole drilled approximately 23cm from the buckle end. Two pieces per rowing machine. Sold individually. -
For use with Model A, B, C and original D Indoor Rowers. Replacement nylon footstrap with buckle, approximately 60cm/24" long by 1" wide with a screwhole drilled approximately 7" from the buckle end. Two per machine. Sold individually. -
For use with the black SkiErg2 -
For use with model C, D and E RowErgs. -
For use with the black SkiErg, the SkiErg Handle Hooks attach to both sides of the SkiErg near the monitor and hold the SkiErg handles in place lower on the machine so that the handles are within reach for people using the SkiErg from a wheelchair or seated position. -
T27 6-Lobe driver required to assemble & tighten most screws and fasteners on Concept 2 machines since 2015. Use only with 6-lobe Torx screws & fasteners. -
The Oar Rigging Tool includes the following:- T20 Torx Driver for adjusting:
- The grip clamp screw
- The length adjustment screw on suede scull grips
- 6 mm Hex Nut Driver, for adjusting the length adjustment screws on adjustable grips (excluding the suede scull grip)
- #2 Phillips Bit for adjusting:
- Older grip clamp screws
- Length on older oars
- 5/16" Hex Nut Driver for adjust the collar band clamp
- T20 Torx Driver for adjusting:
-
For use with the handle on all models of indoor rowers. Connects the handle to the chain. The corresponding nuts are part number 240 for a Model A, B or C and part number 1235 for Model D, E and Dynamic -
For use with Model A, B, updated D, E, Dynamic Indoor rowers and the black SkiErgs manufactured from August 2014–present. This is the right caster wheel. -
For use with Model A, B, updated D, E, Dynamic Indoor rowers and the black SkiErgs manufactured from August 2014–present. This is the left caster wheel. -
FREE SHIPPINGFor use with Model C, D and E Indoor Rowers. This is the handle hook used on the Models C, D and E Indoor Rower. To store the handle long-term, place the handle up against the flywheel housing. For ease of use before or during a workout, placing the handle in the handle hook puts the handle within easy reach. Includes hardware. -
Replacement grip for sculling oar handles. Ice blue rubber with longitudinal ribs. Fits wood handles, bonded composite handles, or old style 10cm adjustable-length handles. -
Replacement grip for sculling oar handles. Azure blue rubber with longitudinal ribs. Fits wood handles, bonded composite handles, or old style 10 cm adjustable-length handles. -
Replacement grip for sculling oar handles. Made of smooth, black rubber. Fits wood handles, bonded composite handles, or old style 10 cm adjustable-length handles. -
Scull collar for use with green or black Concept2 sleeves. -
For use with the updated Model D, Model E and Dynamic Indoor Rowers. Right footstretcher cover. The flextfoot piece (part number (part number 1063, sold separately) fits into this part to make the complete footstretcher assembly. Footplate/Flexfoot Assembly Diagram -
This is a replacement case back for the PM5 monitor. It includes the battery contacts. Compatible with PM5 monitors only. -
This is a replacement case back for the PM5 monitor. It includes the battery contacts. Compatible with PM5 monitors only.
