-
One full rake of scull bushings for 13mm pins. Bushings are sold in units called rakes. Each rake of pitch bushings is enough for two oarlocks. Bushings allow for pitch adjustment anywhere from one to seven degrees. -
Out of stock
Concept 2 Sculling oarlock -
Used in various places with Model D and Model E Indoor Rowers manufactured from August 2006–present. -
For use with Model D and Model E Indoor Rowers manufactured from August 2006–present. This screw is used on the foot stretcher bellies and two required for P/N 1101 Hanger Shaft, threaded. For master schematics of all model indoor rowers, visit Manuals and Schematics. -
For use with all Model D and Model E Indoor Rowers manufactured from August 2006–present. Two P/N 1243 Hex Cap Screw (For hanger shafts) may be required. For master schematics of all model indoor rowers, visit Manuals and Schematics. -
For use on all Model C, D and E Indoor Rowers. This swivel bushing is installed at the swivel/handle end of the chain to prolong chain life and provide smoother rowing. See more info. -
This is a replacement case back for the PM5 monitor. It includes the battery contacts. Compatible with PM5 monitors only. -
This is a replacement case back for the PM5 monitor. It includes the battery contacts. Compatible with PM5 monitors only. -
Replacement sensor unit and housing for the BikeERG -
This is a replacement LCD and housing front for the PM5 monitor. If your LCD is cracked or damaged, you can replace it with this replacement part. Compatible with PM5 monitors only. PM5 LCD Replacement Instructions -
FREE SHIPPINGFor use on the Model D and E Indoor Rower and RowERG. -
For use with Model C, D, E and Dynamic Indoor Rowers. One of the 82mm (3.25") wide top seat rollers (two per machine; sold individually) that runs on the stainless steel track on the monorail. Mounting hardware that holds the roller on the seat frame is not included, because it can usually be re-used. -
Out of stock
FREE SHIPPINGThe Polar H9 chest strap (65-107cm) offers reliable and high-quality heart rate measurement. It supports all common transmission technologies. That would be Bluetooth, ANT+ and analog 5kHz technology. PM5 Monitor: The Polar H9 can be paired with the PM5 monitor either via Bluetooth or via ANT+. Scope of delivery:- Polar H9 heart rate sensor
- Polar Soft Strap
- Polar H9 quick guide
-
The Oar Rigging Tool includes the following:- T20 Torx Driver for adjusting:
- The grip clamp screw
- The length adjustment screw on suede scull grips
- 6 mm Hex Nut Driver, for adjusting the length adjustment screws on adjustable grips (excluding the suede scull grip)
- #2 Phillips Bit for adjusting:
- Older grip clamp screws
- Length on older oars
- 5/16" Hex Nut Driver for adjust the collar band clamp
- T20 Torx Driver for adjusting:
-
For use on the Model D and E Indoor Rower. This is the 14 tooth sprocket for the flywheel axle. If you need to replace the sprocket, you should replace the chain at the same time (see part number 1916). -
For use with Model C, D and E Indoor Rowers & RowERG. Includes on 8' 4" long chain with a brass swivel at the handle end and chain connector for the inside end. If your chain is badly rusted, has seized links or is broken, you will need to replace it with this part. -
This is the 380cm (12´ 6") long elastic shock cord (or bungee cord) that recoils the chain on recovery. -
For use with Model A, B, C and original D Indoor Rowers. Replacement nylon footstrap with buckle, approximately 60cm/24" long by 1" wide with a screwhole drilled approximately 7" from the buckle end. Two per machine. Sold individually. -
This footstrap will only work for indoor rowers made after July 21, 2006. If your indoor rower was made before July 21, 2006, order P/N 1501 Footstrap (Single) Model A, B, C & Early D - 60cm/24"
instead. Replacement nylon footstrap with buckle, approximately 75cm long by 2.5cm wide, with a screw hole drilled approximately 23cm from the buckle end. Two pieces per rowing machine. Sold individually. -
FREE SHIPPINGUse on all black SkiErgs manufactured from August 2014 to present, or any gray SkiErgs that have already been retrofitted with this grip. Contains two handles and two plugs. Instructions for the correct exchange of grips can be found here: (SkiErg 2) https://www.concept2.de/files/pdf/us/skierg/skierg2_instrux_handle_replace.pdf -
- Adjustable replacement handle (5cm) made from contoured orange rubber. Finger-sized radial contours and brushed texture. Solid, durable material. Available in two diameters: 32mm (thin) or 33.5mm (medium). Available separately.
-
- Available on fixed composite handles and with our Length Adjustment System
- 32–39 mm outside hand diameter, depending on handle and shaft (see chart)
- 43 mm inside hand diameter
- Firm, smooth texture
- Most durable, easy to clean
-
- Available on fixed composite handles and with our Length Adjustment System
- 32–39 mm outside hand diameter, depending on handle and shaft (see chart)
- 43 mm inside hand diameter
- Firm, smooth texture
- Most durable, easy to clean
-
- Available on fixed composite handles and with our Length Adjustment System
- 32–39 mm outside hand diameter, depending on handle and shaft (see chart)
- 43 mm inside hand diameter
- Firm, smooth texture
- Most durable, easy to clean
-
For use with Model A and C Indoor Rowers. This is the pickup (sensor) and cable (wire) that transmit flywheel to the Performance Monitor on your indoor rower.
