-
For use on all Model B, C, D, E and Dynamic Indoor Rowers. This is the R8 bearing located outside of the flywheel. The corresponding bearing cup (part number 1013 or 258 depending on which model you have) is sold separately. -
For use with RowErgs, Model D Indoor Rowers manufactured from November 2006–present and Model E Indoor Rowers. -
For use with all Model D and Model E Indoor Rowers manufactured from August 2006–present. Two P/N 1243 Hex Cap Screw (For hanger shafts) may be required. For master schematics of all model indoor rowers, visit Manuals and Schematics. -
For use on all Model C, D and E Indoor Rowers. This is the 17mm bearing located outside of the flywheel. The corresponding bearing cup (part number 1012) is sold separately. -
For use on SkiErgs manufactured from August 2014–present. Used at the top bracket and frame cap. There are 4 of part PN2834 in the SkiErg. SkiErg Schematics -
Chain Idler Pulley
-
6mm L-Key (or Allen Key) for use in assembling and maintaining the Concept 2 BikeERG -
This footstrap will only work for indoor rowers made after July 21, 2006. If your indoor rower was made before July 21, 2006, order P/N 1501 Footstrap (Single) Model A, B, C & Early D - 60cm/24"
instead. Replacement nylon footstrap with buckle, approximately 75cm long by 2.5cm wide, with a screw hole drilled approximately 23cm from the buckle end. Two pieces per rowing machine. Sold individually. -
For use with Model A, B, C and original D Indoor Rowers. Replacement nylon footstrap with buckle, approximately 60cm/24" long by 1" wide with a screwhole drilled approximately 7" from the buckle end. Two per machine. Sold individually. -
Out of stock
For use with the black SkiErg2 -
For use with model C, D and E RowErgs. -
This is a replacement case back for the PM5 monitor. It includes the battery contacts. Compatible with PM5 monitors only. -
This is a replacement case back for the PM5 monitor. It includes the battery contacts. Compatible with PM5 monitors only. -
For use with the black SkiErg, the SkiErg Handle Hooks attach to both sides of the SkiErg near the monitor and hold the SkiErg handles in place lower on the machine so that the handles are within reach for people using the SkiErg from a wheelchair or seated position. -
T27 6-Lobe driver required to assemble & tighten most screws and fasteners on Concept 2 machines since 2015. Use only with 6-lobe Torx screws & fasteners. -
The Oar Rigging Tool includes the following:- T20 Torx Driver for adjusting:
- The grip clamp screw
- The length adjustment screw on suede scull grips
- 6 mm Hex Nut Driver, for adjusting the length adjustment screws on adjustable grips (excluding the suede scull grip)
- #2 Phillips Bit for adjusting:
- Older grip clamp screws
- Length on older oars
- 5/16" Hex Nut Driver for adjust the collar band clamp
- T20 Torx Driver for adjusting:
-
For use with the handle on all models of indoor rowers. Connects the handle to the chain. The corresponding nuts are part number 240 for a Model A, B or C and part number 1235 for Model D, E and Dynamic -
For use with Model A, B, updated D, E, Dynamic Indoor rowers and the black SkiErgs manufactured from August 2014–present. This is the right caster wheel. -
For use with Model A, B, updated D, E, Dynamic Indoor rowers and the black SkiErgs manufactured from August 2014–present. This is the left caster wheel. -
For use with RowERG, Model D and E Indoor Rowers. This is the housing into which a sensor coil sits. *** SENSOR COIL NOT INCLUDED *** Replacement Instructions (also available at concept2.co.uk/service): -
For use with Model C, D and E Indoor Rowers. This is the handle hook used on the Models C, D and E Indoor Rower. To store the handle long-term, place the handle up against the flywheel housing. For ease of use before or during a workout, placing the handle in the handle hook puts the handle within easy reach. Includes hardware. -
Sale!
It's hard. It's black. It's not plastic. That's good. And contains 500,000,000 micro-mililitres of powered up H2O. In other words - it's a 500ml steel bottle for your water. Get one. Forget it somewhere - Buy another. -
Replacement grip for sculling oar handles. Ice blue rubber with longitudinal ribs. Fits wood handles, bonded composite handles, or old style 10cm adjustable-length handles.
